Silfluo

Fluorinated Electronic Coatings

LC-FC633 — Fluorinated Conformal Coating with Fluorescent Inspection

LC-FC633 is a clear, glossy fluoropolymer coating with a built-in fluorescent tracer, so coverage on PCBAs and precision parts can be checked under UV light while the film stays colorless in normal viewing. Films run 0.5–2.5 µm per coat, with a water contact angle of ≥110° and surface free energy of 10–11 mN/m.

Packaging
100 g – 25 kg
Shelf life
24 months, 5–35 °C
Flash point
None (carrier)
Documents
TDS · SDS · COA
Request a Sample
Mechanical watch movement with gears and balance wheel — precision-mechanism application context for LC-FC633 fluorinated coating

Product Overview

The 2%, 5% and 10% solids grades give 0.5–1.0 µm, 1.0–1.5 µm and 1.5–2.5 µm per coat — the 2% grade is the thinnest listed film in the LC-FC series — and are tack-free in roughly 30 seconds, 1 minute and 2 minutes. The fluorinated carrier has no flash point and a 50–68 °C boiling range.

Oil repellency is an n-hexadecane contact angle of ≥75°, with light transmittance above 90%, a glass-transition temperature of 5–10 °C and a 1% mass-loss temperature of about 260 °C. The thermal figures are analysis results and do not alone establish service temperature or reflow compatibility. The product is zero-ODP and RoHS compliant.

Key Benefits

Clear film, traceable coverage

The fluorescent tracer reveals skips under UV inspection while the cured film remains colorless in daylight.

Thinnest entry grade

LC-FC633-2 lays down 0.5–1.0 µm per coat, the lowest listed film build of any LC-FC grade.

Low surface energy

10–11 mN/m with contact angles of ≥110° for water and ≥75° for n-hexadecane reduces wetting by moisture, condensation and oils.

Ambient drying in minutes

Tack-free in about 30 seconds to 2 minutes depending on grade, with no heat step and no flash point.

Typical Applications

  • PCBA and flexible circuit protection with fluorescent coverage inspection
  • Epilame / lubricant anti-migration treatment for watches, micro-motors, cameras and other precision mechanisms
  • Contamination and lubricant-migration barrier for HDD MR read heads
  • Precision parts, MEMS devices and miniaturized sensors needing low film build

Solution guides: Electronics & PCBPrecision Parts & Watches

Technical Data

Typical Properties
Test ItemPerformance IndicatorTest Method
Film TypeStandard type—
Active Ingredient / CarrierFluoropolymer in non-flammable fluorinated solvent—
Appearance (liquid)Colorless transparent liquid—
Solid Content Grades2%, 5%, 10% (other concentrations on request)—
Dynamic Viscosity, 25 °C10–30 mPa·s—
Flash Point / Boiling RangeNo flash point · 50–68 °C—
Cured Film Color / GlossColorless · Glossy—
Light Transmittance>90%—
Inspection AidFluorescent tracer—
Static Water Contact Angle≥110°—
Static n-Hexadecane Contact Angle≥75°—
Surface Free Energy10–11 mN/m—
Adhesion5BASTM D3359
Glass Transition Temperature (Tg)5–10 °C—
Thermal Stability (1% mass loss)~260 °C—
Dielectric Constant3.1—
Volume Resistivity / Surface Resistivity>10¹⁴ Ω·m · >10¹⁴ Ω/sq—
Application Parameters
Single-Coat Dry Film Thickness (2% / 5% / 10% grades)0.5–1.0 / 1.0–1.5 / 1.5–2.5 µm
Tack-Free Time, ambient (2% / 5% / 10% grades)30 s / 1 min / 2 min
Application MethodsApply by spray, dip, roll or blade coating; stainless-steel or PTFE-lined equipment
EnvironmentalZero ODP; RoHS compliant
Storage Temperature / Shelf Life5–35 °C · 24 months unopened

Values from the LC-FC633 technical data sheet. Complete TDS with test conditions available on request.

Application & Processing Guidance

Coat by spray, dip, roll or blade using stainless-steel or PTFE-lined equipment, and fix withdrawal speed or spray settings in trials on the intended part. Ventilate spray areas with local exhaust.

Inspect under UV light after drying to locate skips, then touch up. Mask contacts unless the assembly process has been validated with the coating, confirm the tracer is acceptable where device cleanliness is critical, and verify thermal-cycling performance under your product test protocol.

Substrate Compatibility

May be evaluated on PCBAs and flexible circuits, lubricated components in watches, micro-motors and cameras, HDD read heads, MEMS devices and miniaturized sensors. Adhesion is listed as 5B (ASTM D3359); confirm it, together with tracer visibility, on your own parts.

LC-FC633 — Purchasing & Application FAQ

How do I inspect LC-FC633 coverage?

Under a UV lamp once the film is tack-free: coated areas fluoresce and skips stay dark. In daylight the film is clear and glossy, so it does not change the look of the part.

Which solids level should I use?

Use LC-FC633-2 (0.5–1.0 µm) where every micron counts, LC-FC633-5 (1.0–1.5 µm) as the middle option, and LC-FC633-10 (1.5–2.5 µm) for more film per pass. Other concentrations are available on request.

Can LC-FC633 stand in for a thick conformal coating?

No. It protects with a film of a few microns against moisture, condensation, dust and oils; it is not a thick-film mechanical or high-dielectric barrier. For thick-film protection, look at the LC-CC conformal coatings.

TDS / SDS / COA & Samples

Technical Data Sheet, Safety Data Sheet and batch Certificate of Analysis are available for LC-FC633, and a COA accompanies every shipment. Evaluation samples ship with starting-parameter guidance.

Packaging: 100 g, 500 g, 1 kg and 25 kg packs. Shelf life 24 months from manufacture in unopened containers stored at 5–35 °C, away from sunlight, heat and ignition sources.

SDS & batch COA on request · Reply within 1 business day.

Reply within 1 business day