Silfluo

Fluorinated Electronic Coatings

LC-FC181/183 — High-Oleophobic Fluorinated Conformal Coating Series

LC-FC181 and LC-FC183 are the most oil-repellent grades in the Silfluo fluorinated coating range: the glossy film reaches a water contact angle of ≥118°, an n-hexadecane contact angle of ≥80° and surface free energy of 8–10 mN/m. LC-FC181 dries clear; LC-FC183 adds a fluorescent tracer for coverage inspection.

Packaging
100 g – 25 kg
Shelf life
24 months, 5–35 °C
Flash point
None (carrier)
Documents
TDS · SDS · COA
Request a Sample
Miniature ball bearings on a white surface — precision-part application context for LC-FC181/183 fluorinated coating

Product Overview

Both are fluoropolymers in a non-flammable fluorinated carrier, supplied at 2%, 5% and 10% solids. Film build spans the widest range in the series — 0.5–1.5 µm for the 2% grade, 1.5–2.5 µm for 5% and 3–10 µm for 10% — so one chemistry covers near-invisible epilame treatments as well as heavier protective films on PCBAs.

Thermal-analysis values sit above LC-FC130: a melting point of 70–80 °C and a 1% mass-loss temperature of about 260 °C. These figures do not by themselves define a continuous service temperature or reflow-soldering compatibility, and solderability and solvent removability must be confirmed under your process conditions. The product has zero ozone depletion potential and is RoHS compliant.

Key Benefits

Highest listed oil repellency

An n-hexadecane contact angle of ≥80° and surface free energy of 8–10 mN/m resist wetting by lubricants, oil mist and skin oils.

Fluorescent option

LC-FC183 shows coverage under UV inspection light; LC-FC181 stays tracer-free where fluorescence is not wanted.

Up to 10 µm in one coat

The 10% grade builds 3–10 µm per coat, the thickest single-coat film in the LC-FC series.

Glossy, high-clarity film

Light transmittance above 91% keeps the coating unobtrusive on transparent or light-colored parts.

Quick ambient drying

Tack-free in about 30 seconds (2%), 1 minute (5%) or 2 minutes (10%), with no flash point to manage.

Typical Applications

  • PCBA and flexible circuit protection; LC-FC183 for fluorescent coverage inspection
  • Epilame / lubricant anti-migration treatment for watches, micro-motors, cameras and other precision mechanisms
  • Contamination and lubricant-migration barrier for HDD MR read heads
  • Precision parts, MEMS devices and miniaturized sensors needing low film build

Solution guides: Electronics & PCBPrecision Parts & Watches

Technical Data

Typical Properties
Test ItemPerformance IndicatorTest Method
Film TypeHigh oleophobic type—
Active Ingredient / CarrierFluoropolymer in non-flammable fluorinated solvent—
Appearance (liquid)Colorless transparent liquid—
Solid Content Grades2%, 5%, 10% (other concentrations on request)—
Dynamic Viscosity, 25 °C10–30 mPa·s—
Flash Point / Boiling RangeNo flash point · 50–68 °C—
Cured Film Color / GlossColorless · Glossy—
Light Transmittance>91%—
Inspection AidFluorescent tracer (LC-FC183 only)—
Static Water Contact Angle≥118°—
Static n-Hexadecane Contact Angle≥80°—
Surface Free Energy8–10 mN/m—
Adhesion5BASTM D3359
Melting Point70–80 °C—
Thermal Stability (1% mass loss)~260 °C—
Dielectric Constant3.1—
Volume Resistivity / Surface Resistivity>10¹⁴ Ω·m · >10¹⁴ Ω/sq—
Application Parameters
Single-Coat Dry Film Thickness (2% / 5% / 10% grades)0.5–1.5 / 1.5–2.5 / 3–10 µm
Tack-Free Time, ambient (2% / 5% / 10% grades)30 s / 1 min / 2 min
Application MethodsApply by spray, dip, roll or blade coating; stainless-steel or PTFE-lined equipment
EnvironmentalZero ODP; RoHS compliant
Storage Temperature / Shelf Life5–35 °C · 24 months unopened

Values from the LC-FC181/183 technical data sheet. Complete TDS with test conditions available on request.

Application & Processing Guidance

Spray, dip, roll or blade-coat with stainless-steel or PTFE-lined equipment. For the 10% grade, set dip withdrawal speed or spray passes carefully: the 3–10 µm window is wide, and thickness drives both the uniformity of repellency and appearance.

With LC-FC183, inspect coverage under a UV lamp once the film is tack-free. Mask contacts unless solderability and rework have been validated with the coating, and keep local exhaust running during spraying.

Substrate Compatibility

May be evaluated on PCBAs and flexible circuits, lubricated parts in precision mechanisms, HDD read-head assemblies, and MEMS devices or miniaturized sensors; adhesion is listed as 5B (ASTM D3359). Confirm adhesion, solderability and functional performance on your own parts and surface preparation.

LC-FC181/183 — Purchasing & Application FAQ

What is the difference between LC-FC181 and LC-FC183?

Only the fluorescent tracer. LC-FC183 contains it for UV coverage inspection; LC-FC181 is the same clear film without it. Both are offered in 2%, 5% and 10% solids.

Is LC-FC181/183 compatible with reflow soldering?

Not established. The 1% mass-loss temperature of about 260 °C is a thermal-analysis result and does not on its own prove reflow compatibility. Test solderability, appearance and adhesion through your actual reflow profile before use.

Which grade should I try for lubricant anti-migration?

Start with the 2% grade, which gives the thinnest film of this series (0.5–1.5 µm). Epilame performance depends on the lubricant, substrate, surface preparation and thickness, so compare treated and untreated parts with your own oil.

Can it be used on HDD heads or MEMS devices?

These are potential uses that need validation. Film thickness, adhesion, electrical performance and cleanliness must be confirmed for each device before production; no electronic-grade purity specification is published for this series.

TDS / SDS / COA & Samples

Technical Data Sheet, Safety Data Sheet and batch Certificate of Analysis are available for LC-FC181/183, and a COA accompanies every shipment. Evaluation samples ship with starting-parameter guidance.

Packaging: 100 g, 500 g, 1 kg and 25 kg packs. Shelf life 24 months from manufacture in unopened containers stored at 5–35 °C, away from sunlight, heat and ignition sources.

SDS & batch COA on request · Reply within 1 business day.

Reply within 1 business day