Silfluo
Open paint cans and paintbrushes on a teal, grey and peach colour-blocked background

Application Solution

Coatings & PaintsSilicone additives for flow, leveling and substrate wetting

20–3000 cSt

Viscosity span across grades

Wide pH

Wetting with leveling (LF-2506)

Reactive

Resin-modification option (LF-1221)

Many coating defects form at the surface while the film is still wet: craters around contaminants, Bénard cells as solvent evaporates, colour floating and flooding, poor spreading on low-energy substrates, and films that block or feel rough once dry. Polyether-modified silicone additives work at that surface by lowering and evening out surface tension.

Silfluo offers two groups. Silicone leveling agents handle flow, crater control, slip, anti-blocking and recoatability in organic coatings. Substrate wetting agents help waterborne industrial coatings spread over difficult substrates. The right grade depends on the defect, the resin system and whether the coating is waterborne or solvent-borne.

The TDS for these additives covers composition, viscosity and function only, so this page helps you decide which grades to trial; addition level and compatibility come from your own tests.

Service Conditions Covered

Coating typesOrganic resin coatings (leveling agents) · waterborne industrial coatings (substrate wetting agents)
Defects addressedCratering, Bénard cells, pigment floating and flooding, poor substrate wetting, low slip, blocking, recoat problems
Viscosity range20–50 cSt (LF-2502) to 2000–3000 cSt (LF-1442)
Extra propertiesLow foam (LF-1443, LF-2505) · acid and alkali resistance (LF-1444, LF-2505) · broad or wide pH (LF-2502, LF-2506) · clear liquid (LF-2504) · reactive (LF-1221)
Supply12 months shelf life unopened at room temperature; shipped as non-dangerous goods

Recommended Products & Why

Grade Viscosity (25 °C)Key Function Why this grade
LF-1344 600–1000 cStFlow, leveling, anti-floating; slip Flow and surface-defect control during drying: helps suppress Bénard cells, reduces cratering and pigment floating, and adds slip to the dried film.
LF-1444 600–1000 cStLeveling; recoatable; acid/alkali resistant Leveling for recoatable systems with acid and alkali resistance; same viscosity range as LF-1344, chosen when later coats must still adhere.
LF-1442 2000–3000 cStSlip, anti-blocking, anti-cratering Highest-viscosity grade at 2000–3000 cSt, aimed at surface slip and anti-blocking, with leveling and crater control as secondary effects.
LF-1400 300–500 cStBroad compatibility; flow and slip Broad compatibility across resin systems for flow, smoothness and slip, for complex formulations where incompatibility is the main risk.
LF-1443 500–1000 cStWetting, leveling, smooth feel; low foam Wetting, leveling and a smooth hand feel with a low contribution to foam, for systems already prone to foaming.
LF-1221 200–500 cStReactive; wetting and leveling Reactive grade that can be built into the resin to add lubricity, softness and water repellency on top of wetting and leveling.
LF-2502 20–50 cStSubstrate wetting; broad pH range Low-viscosity waterborne wetting agent for low-surface-energy substrates, supporting uniform films across a broad pH range.
LF-2504 40–100 cStSubstrate wetting and leveling; clear liquid Clear liquid wetting agent for waterborne coatings that also supports leveling, where a clear additive is required.
LF-2505 200–300 cStSubstrate wetting; low foam; acid/alkali resistant Waterborne wetting with low foam and resistance to acidic or alkaline conditions; supplied as a yellow transparent liquid.
LF-2506 20–40 cStWetting, leveling and slip; wide pH Wetting, leveling and slip over a wide pH range while limiting foam stabilization, as a single additive in simpler formulations.

Table values from each product's TDS; “—” = not listed in that TDS.

Surface Preparation & Application Principles

Identify the defect before choosing the additive. Craters and Bénard cells point to a leveling agent; retraction and poor coverage on low-energy substrates point to a wetting agent; blocking and rough feel point to a slip grade.

Add silicone additives in small steps and compare each level against an untreated control panel, checking appearance, foam and adhesion together rather than the target defect alone.

Check recoatability and intercoat adhesion whenever a silicone additive goes into a primer or intermediate coat, or start with LF-1444 where recoating is part of the system.

Trial one or two matched grades against your current additive at the same addition level, rather than several similar grades at once; side-by-side results are easier to read.

Applicability Boundaries & What We Confirm

  • Dosage, VOC and certification figures are not stated in our TDS, and we do not publish them.
  • Substrate wetting agents are described for waterborne industrial coatings; use in solvent-borne systems needs testing.
  • Silicone additives can affect recoating and intercoat adhesion in some systems; verify adhesion before production.
  • What we confirm: waterborne or solvent-borne, resin system, substrate, the defect, the additive you use now and why you want to change, and whether the trial is for development or production.

Discuss your project with an engineer

Send your substrate, service conditions and current coating problem — we reply with a concrete system proposal within 1 business day.

Discuss Your Project

Reply within 1 business day