Silfluo

Conformal Coatings

Silfluo conformal coatings are ready-to-use protective films for printed circuit board assemblies, and the first choice is how they cure on your line. LC-CC1390 series is a moisture-cure silicone for -40 to +200 °C service, LC-CC7900-150D is a solvent-free UV/moisture dual-cure coating for fast lines with shadowed areas, and LC-CC8102 is a solvent-evaporation acrylic that can be removed for rework.

Every grade carries a fluorescent tracer, so coverage can be checked under a 365 nm blacklight. These are thin conformal films, not potting compounds: if a design calls for encapsulating components in epoxy or polyurethane, that is a different product category and these coatings are not a substitute.

Who This Line Is For

Product Comparison

Grade Product Base ChemistryUV InspectionService TemperatureCure MechanismTransport Classification
LC-CC1390 Single-Component Silicone Conformal Coating Series Single-component silicone, moisture cureUV fluorescent tracer, visible under 365 nm blacklight-40 to +200 °CAtmospheric moisture at room temperature, or accelerated by heatLC-CC1397: non-dangerous goods; other grades: dangerous goods
LC-CC7900-150D UV/Moisture Dual-Cure Conformal Coating Polyurethane acrylate, solvent-freeFluorescent tracer, visible under 365 nm blacklight-60 to +135 °CUV cure; moisture cure in shadowed areasNon-dangerous goods
LC-CC8102 Single-Component Acrylic Conformal Coating Modified acrylic, low-toxicity solventsFluorescent tracer, visible under 365 nm blacklight-40 to +120 °CSolvent evaporationDangerous goods

Comparison values from each product's TDS; “—” = not listed for that grade; see its product page and TDS.

How to Choose

Cure mechanism and line equipment

LC-CC1390 series cures with atmospheric moisture: full cure in under 24 hours at 25 °C and 60% RH, and the TDS recommends at least 20 °C and 40% RH. LC-CC7900-150D needs a UV dose of at least 1000 mJ/cm² to surface-dry. LC-CC8102 dries by solvent evaporation, tack-free in 5 minutes at 80 µm.

Shadowed areas

Through-hole parts, tall SMD components and connector housings block UV light. LC-CC7900-150D finishes these zones by a secondary moisture cure with no extra process step: basic cure in about 3 days at 23 °C and 50% RH, ultimate properties in 7–14 days.

Temperature range and film flexibility

LC-CC1390 series forms a silicone elastomer rated -40 to +200 °C, from Shore A 20–30 (LC-CC1394) to 70–80. LC-CC7900-150D covers -60 to +135 °C with 199% elongation at break. LC-CC8102 covers -40 to +120 °C with 20% elongation.

Rework

If boards must be repaired after coating, LC-CC8102 is the reworkable option: the acrylic film comes off with a conformal coating remover. Silicone and UV-cured films are harder to remove locally, so settle rework expectations before you choose.

Solvents, EHS and shipping

LC-CC7900-150D and LC-CC1397 are solvent-free and ship as non-dangerous goods. The other LC-CC1390 grades contain toluene or solvent oil No. 120, and LC-CC8102 uses low-toxicity solvents; these ship as dangerous goods.

Related Applications

Electronics & PCB →

Conformal Coatings — FAQ

Silicone, acrylic or UV dual-cure: which conformal coating should I choose?

Match the chemistry to your line and service. Silicone (LC-CC1390 series) suits wide temperature swings up to +200 °C and flexible films. UV dual-cure (LC-CC7900-150D) suits high-volume lines with UV equipment and shadowed components. Acrylic (LC-CC8102) suits fast drying and boards that need rework.

Will a UV-curable coating cure under tall components and connectors?

UV light alone will not reach those areas. LC-CC7900-150D contains a secondary moisture-cure mechanism that crosslinks the coating in shadowed zones after UV exposure, reaching basic cure in about 3 days at 23 °C and 50% RH.

Can the coating be removed to repair a board?

LC-CC8102 can be removed with a conformal coating remover, so components can be repaired or replaced without mechanical damage to the board. For silicone or UV-cured coatings, plan local removal methods during process qualification.

What should I send to get a coating recommendation?

Tell us the board type and failure environment, how you coat (spray, dip, brush, dispensing or selective coating), whether you have UV lamps or ovens, the target thickness and rework needs, and which humidity, salt spray, corrosive gas or thermal cycling tests the board must pass.

Not sure which grade fits your process?

Send us your substrate, application method and service conditions — our technical team replies within 1 business day.

Request Technical Recommendation