Silfluo

Conformal Coatings

LC-CC1390 — Single-Component Silicone Conformal Coating Series

LC-CC1390 is a family of five single-component silicone conformal coatings that cure with atmospheric moisture into an elastomeric film with a −40 to +200 °C service range. Four solvent-borne grades and the solvent-free LC-CC1397 let you match solvent, film hardness and transport class to your line, and every grade carries a UV tracer for 365 nm inspection.

Packaging
20 kg / 200 kg drums
Shelf life
6 months, 0–30 °C
Transport
DG, except LC-CC1397
Documents
TDS · SDS · COA
Request a Sample
Populated printed circuit board with SMD components and a large IC — typical application for LC-CC1390 silicone conformal coating

Product Overview

The grades fall into two hardness families. LC-CC1390, LC-CC1392 and LC-CC1398 cure to Shore A 70–80 for rigid boards where film hardness and abrasion resistance come first. LC-CC1394 cures to Shore A 20–30 for assemblies that see vibration, thermal-expansion mismatch or flexing substrates, and LC-CC1397 sits between them at Shore A 55–65.

Solvent is the other lever. LC-CC1390 is toluene-based; LC-CC1392, LC-CC1394 and LC-CC1398 use solvent oil No. 120, a lower-aromatic option. LC-CC1397 is solvent-free at 98% solids and is stored and shipped as non-dangerous goods, which suits enclosed or low-ventilation lines and logistics-sensitive supply chains. LC-CC1398 pairs 89% solids with a 5–15 minute surface dry for faster processing.

Key Benefits

Wide thermal-cycling window

The silicone elastomer film absorbs differential expansion across −40 to +200 °C without delaminating or cracking — relevant for boards that swing between cold starts and hot operation.

Broad environmental protection

Moisture and condensation, salt spray, sulfur gases (H2S, SO2), mold growth and oxidizing atmospheres are all covered on the TDS, with dielectric insulation held between conductors.

Coverage you can inspect

A UV fluorescent tracer in every grade shows skips and pinholes under 365 nm blacklight, for manual or automated inspection after surface dry.

A solvent-free option

LC-CC1397 removes solvent entirely at 98% solids and ships as non-dangerous goods, for plants where facility rules or freight restrictions exclude solvent-borne coatings.

Five process fits, one chemistry

Viscosities from 400–800 cP to 1500–2500 cP and surface dry times from 5 to 60 minutes cover brushing, spraying, dipping and automated dispensing.

Typical Applications

  • Consumer electronics and home appliances
  • Smart metering and IoT devices
  • Automotive electronics (engine control units, sensor modules)
  • LED driver boards
  • Aerospace and avionics assemblies
  • Marine electronics
  • Medical device circuit boards
  • Precision communication equipment

Solution guides: Electronics & PCB

Technical Data

Typical Properties
PropertyTypical Value
Base ChemistrySingle-component silicone, moisture cure
AppearanceColorless or light yellow transparent liquid
Solvent (LC-CC1390 / 1392 / 1394 / 1397 / 1398)Toluene / Solvent oil No. 120 / Solvent oil No. 120 / None / Solvent oil No. 120
Solid Content, 150 °C, 2 h (LC-CC1390 / 1392 / 1394 / 1397 / 1398)70±2 / 70±2 / 60±2 / 98 / 89±2 %
Viscosity, 25 °C (LC-CC1390 / 1392 / 1394 / 1397 / 1398)600–1000 / 600–1000 / 400–800 / 1500–2500 / 600–1000 cP
Hardness, Shore A (LC-CC1390 / 1392 / 1394 / 1397 / 1398)70–80 / 70–80 / 20–30 / 55–65 / 70–80
UV InspectionUV fluorescent tracer, visible under 365 nm blacklight
Service Temperature-40 to +200 °C
Application Parameters
Cure MechanismAtmospheric moisture at room temperature, or accelerated by heat
Surface Dry Time, 25 °C, 60% RH, 1.25 mm (LC-CC1390 / 1392 / 1394 / 1397 / 1398)10–30 / 10–30 / 5–15 / 60 / 5–15 min
Complete Curing Time (25 °C, 60% RH, 1.25 mm)<24 h
Minimum Recommended Cure Environment20 °C, 40% RH
Application MethodsBrush, spray, dip or automated dispensing
Storage Temperature / Shelf Life0–30 °C · 6 months unopened
Transport ClassificationLC-CC1397: non-dangerous goods; other grades: dangerous goods

Values from the LC-CC1390 technical data sheet. Complete TDS with test conditions available on request.

Application & Curing Guidance

Clean boards of flux residue, ionic contamination, dust, moisture and grease first — contamination left under the film is the usual cause of adhesion loss and corrosion under humidity. Mask connectors, test points, switch contacts, potentiometers and heat-sink mounting faces, and remove the masking after surface dry.

Apply by brush, spray, dip or automated dispensing as an even film without sags, pinholes or skips. Spray the solvent-borne grades in a ventilated booth with local exhaust and explosion-proof equipment. Apply a second coat only once the first is tack-free: 10–30 minutes for LC-CC1390/1392, 5–15 minutes for LC-CC1394/1398 and about 60 minutes for LC-CC1397 at 25 °C and 60% RH.

All grades cure fully in under 24 hours at 25 °C and 60% RH (1.25 mm film). Heat and higher humidity speed up cure; below the minimum recommended environment of 20 °C and 40% RH, allow longer and confirm cure by Shore A hardness before service. Reseal containers immediately after dispensing, because the coating cures with moisture in the can as well as on the board.

Substrate Compatibility

Adheres to metals, printed circuit boards and common electronic substrates. Rigid boards suit the Shore A 70–80 grades; flexible circuits and assemblies with mismatched expansion suit LC-CC1394. Confirm adhesion on your solder mask, component bodies and connector plastics in a line trial before production qualification.

LC-CC1390 — Purchasing & Application FAQ

Which LC-CC1390 grade should I start with?

Start from hardness and solvent. Rigid PCBs where toluene is acceptable: LC-CC1390. A lower-aromatic solvent: LC-CC1392. Soft, vibration-tolerant films: LC-CC1394 (Shore A 20–30). Solvent-free processing or freight limits: LC-CC1397. High solids with a fast surface dry: LC-CC1398 (89% solids).

Can the series be cured faster with heat?

Yes. Elevated temperature and humidity accelerate the moisture cure. Set the oven profile within your components' temperature limits, then confirm full cure by Shore A hardness before electrical testing.

Is LC-CC1397 shipped as dangerous goods?

No. LC-CC1397 is solvent-free and is stored and transported as non-dangerous goods. LC-CC1390, LC-CC1392, LC-CC1394 and LC-CC1398 contain flammable solvent and ship as dangerous goods.

What storage and shelf life does the series need?

Store at 0–30 °C away from sunlight and ignition sources. Shelf life is 6 months from manufacture in unopened containers; material past that date can be retested for viscosity, surface dry time and Shore A hardness at 24 hours before production use.

TDS / SDS / COA & Samples

Technical Data Sheet, Safety Data Sheet and batch Certificate of Analysis are available for LC-CC1390, and a COA accompanies every shipment. Evaluation samples ship with starting-parameter guidance.

Packaging: 20 kg and 200 kg iron drums; other pack sizes on request. Shelf life 6 months unopened at 0–30 °C.

SDS & batch COA on request · Reply within 1 business day.

Reply within 1 business day