Silfluo

Fluorinated Release Agents & Surface Additives

This category groups fluorinated materials that lower the surface energy of a coating. Two are release agents that give a film low, stable release force: FRA-500L/20000, a solvent-free platinum-cured system, and FRA-C10, a two-component solvent-borne fluorocarbon system. The third, LS-53C, is a PFPE-modified acrylic additive that makes UV-curable and acrylic coatings repel water, oil and fingerprints.

Release-film coaters and hard-coat formulators buy these for different reasons, but all three are formulation materials. Coat weight, cure schedule and dosage are set in your own trials, with the TDS values as the starting point; we help you plan those trials rather than quote figures the TDS does not contain.

Who This Line Is For

Product Comparison

Grade Product TypeActive ContentRelease ForceSupply FormSolids Content
FRA-500L/20000 Solvent-Free Fluorinated Release Agent Solvent-free fluorinated release agent, platinum cure100%1–3 g; aged increase below 10 gMain agent, used with separate crosslinker—
FRA-C10 Two-Component Solvent-Borne Fluorocarbon Release Agent Two-component solvent-borne fluorocarbon release agent——Part A main agent + Part B curing agent30%
LS-53C PFPE Modified Acrylic Compound PFPE-modified acrylic surface additive30%—Additive for UV-curable and acrylic coating systems—

Comparison values from each product's TDS; “—” = not listed for that grade; see its product page and TDS.

How to Choose

Solvent-free or solvent-borne release

FRA-500L/20000 is 100% active and cures by platinum catalysis with the LF-HF12-M8 crosslinker; it can also be dissolved in butyl acetate, MIBK, MEK or fluorinated solvent. FRA-C10 is a 30% solids two-component system mixed at 2:1 by weight and used within 2 hours.

Viscosity grade

FRA-500L runs at 400–600 mm²/s and FRA-20000 at 18,000–22,000 mm²/s. Choose the grade that fits your coating head and target coat weight, or dilute in the listed solvents to reach your working viscosity.

Release force data

The FRA-500L/20000 TDS gives a release force of 1–3 g with an aged increase below 10 g. The FRA-C10 TDS does not state a release force, so measure it against your adhesive and substrate during trials.

Surface additive instead of a release coat

If the goal is an easy-clean or anti-fingerprint surface rather than a release liner, LS-53C is the material: 30% active, dosed at 0.1–10%, co-curing with the coating resin to give typical contact angles above 100° for water and 70° for oils.

Related Applications

Easy-Clean & Anti-Fingerprint →

Fluorinated Release Agents & Surface Additives — FAQ

Which crosslinker is used with FRA-500L and FRA-20000?

Both main agents are used with the LF-HF12-M8 crosslinker (20–100 mm²/s) in a platinum-catalyzed system. Crosslinker ratio, inhibitor, platinum level, coat weight and cure schedule are set by trials on your line. The crosslinker is a separate component, so include it when you plan samples for a trial.

How long can mixed FRA-C10 be used?

Use the mixed solution within 2 hours. Dilute Part A with an ester solvent first, then mix it with Part B at 2:1 by weight. Mix only what the line will consume inside that window.

Will LS-53C migrate out of the cured coating?

It is designed not to. During cure the PFPE segments move to the surface to form a low-energy layer, while the acrylic backbone co-cures with the coating resin and anchors them in the film. Compatibility still depends on dosage and resin system, so confirm haze and adhesion in your formulation.

Not sure which grade fits your process?

Send us your substrate, application method and service conditions — our technical team replies within 1 business day.

Request Technical Recommendation