Silfluo

Conformal Coatings

LC-CC8102 — Single-Component Acrylic Conformal Coating

LC-CC8102 is a single-component modified acrylic conformal coating that dries by solvent evaporation, is tack-free in about 5 minutes at 23 °C and can be lifted with a conformal coating remover when a component needs repair. It protects PCBs against moisture, salt spray, mildew and corrosive gases from −40 to +120 °C.

Packaging
1 kg / 5 kg
Shelf life
12 months, 5–28 °C
Transport
Dangerous goods
Documents
TDS · SDS · COA
Request a Sample
Close-up of a circuit board with ICs and passive components — typical application for LC-CC8102 acrylic conformal coating

Product Overview

Its low 52 mPa·s viscosity suits spray, dip and brush application, and the published film properties are based on an 80 µm wet film. At that thickness the coating reaches full cure in 24 hours at room temperature, or in 2 hours at 70 °C when line throughput matters.

Electrical isolation holds under humidity and condensation, with volume resistivity of 8.5×10¹⁵ Ω·cm and dielectric strength of 30 kV/mm. Corrosion resistance on the TDS covers salt spray to IEC 60068-2-52 and the atmospheric gases SO2, H2S and Cl2, and a fluorescent tracer lets AOI systems or operators confirm coverage under 365 nm light.

Key Benefits

Reworkable by design

A conformal coating remover lifts the cured film, so components can be repaired or replaced without grinding into the board.

Fast tack-free, early inspection

Tack-free in 5 minutes at 23 °C (80 µm), so coverage can be checked and touched up while the film is still easy to remove.

Ambient or 70 °C cure

Full cure in 24 hours at room temperature, or 2 hours at 70 °C on production lines — no UV equipment needed.

High insulation resistance

8.5×10¹⁵ Ω·cm volume resistivity and 30 kV/mm dielectric strength keep conductors isolated when condensation forms.

Typical Applications

  • PCB protection in smart meters
  • Household and consumer appliance PCBs
  • Automotive electronics
  • Assemblies that need component rework or replacement

Solution guides: Electronics & PCB

Technical Data

Typical Properties
PropertyTypical Value
Base ChemistryModified acrylic, low-toxicity solvents
ColorColorless to light yellow transparent liquid
Viscosity52 mPa·s
Specific Gravity0.83
Hardness (Shore A)60
Adhesion (Cross-Cut Test)Class 0
Elongation at Break20%
Volume Resistivity8.5×10¹⁵ Ω·cm
Dielectric Strength30 kV/mm
Surface Resistance4.3×10¹⁴ Ω
Corrosion ResistanceSalt spray (IEC 60068-2-52); SO2, H2S, Cl2 gases
UV InspectionFluorescent tracer, visible under 365 nm blacklight
Service Temperature-40 to +120 °C
Application Parameters
Cure MechanismSolvent evaporation
Tack-Free Time (23 °C, 80 µm)5 min
Full Cure Time (80 µm)24 h at room temperature, or 2 h at 70 °C
ReworkRemovable with conformal coating remover
Application MethodsSpray, dip, brush
Storage Temperature / Shelf Life5–28 °C · 12 months unopened
Transport ClassificationDangerous goods

Values from the LC-CC8102 technical data sheet. Complete TDS with test conditions available on request.

Application & Curing Guidance

Clean boards with isopropanol or a dedicated PCB cleaner to remove flux residue, dust, grease and ionic contamination; residues left under the film lead to adhesion loss and corrosion under humidity. Stir the container thoroughly so the UV tracer is evenly distributed.

Spray, dip or brush to a wet film of 80 µm — thicker or thinner films change tack-free time, electrical values and flexibility. Keep boards horizontal through the initial flash-off so the film does not pool at edges or thin on vertical faces.

Allow 24 hours at 23 °C and 50% RH before service, or cure 2 hours at 70 °C and let assemblies cool before handling or electrical testing. Inspect under 365 nm blacklight after coating and again after cure. For rework, apply remover to the area, allow it to penetrate, lift the film, then recoat and re-inspect.

Substrate Compatibility

Designed for printed circuit boards and assembled components, with Class 0 cross-cut adhesion on the TDS. With 20% elongation at break and a −40 to +120 °C range, it fits boards in moderate environments; for wider temperature swings compare LC-CC1390 (−40 to +200 °C), and for higher film flexibility LC-CC7900-150D (199% elongation).

LC-CC8102 — Purchasing & Application FAQ

How do I remove LC-CC8102 for rework?

Apply a conformal coating remover to the area, wait for the penetration time given by the remover supplier, then lift the softened film. Recoat the repaired area and re-inspect it under 365 nm light.

Why does the TDS specify an 80 µm wet film?

The published tack-free time, cure times and electrical values were measured at 80 µm. Running much thicker or thinner changes drying speed, flexibility and insulation, so set your spray or dip parameters to that target first.

Is LC-CC8102 shipped as dangerous goods?

Yes. The liquid contains solvent and is transported as dangerous goods. Store it at 5–28 °C away from sunlight and ignition sources; shelf life is 12 months unopened.

TDS / SDS / COA & Samples

Technical Data Sheet, Safety Data Sheet and batch Certificate of Analysis are available for LC-CC8102, and a COA accompanies every shipment. Evaluation samples ship with starting-parameter guidance.

Packaging: 1 kg and 5 kg containers; customized industrial packaging on request. Shelf life 12 months unopened at 5–28 °C.

SDS & batch COA on request · Reply within 1 business day.

Reply within 1 business day